time: L<http://cvs.schmorp.de/libev/ev.html>.
Libev is an event loop: you register interest in certain events (such as a
-file descriptor being readable or a timeout occuring), and it will manage
+file descriptor being readable or a timeout occurring), and it will manage
these event sources and provide your program with events.
To do this, it must take more or less complete control over your process
the beginning of 1970, details are complicated, don't ask). This type is
called C<ev_tstamp>, which is what you should use too. It usually aliases
to the C<double> type in C, and when you need to do any calculations on
-it, you should treat it as such.
+it, you should treat it as some floatingpoint value. Unlike the name
+component C<stamp> might indicate, it is also used for time differences
+throughout libev.
=head1 GLOBAL FUNCTIONS
=item int ev_version_minor ()
-You can find out the major and minor version numbers of the library
+You can find out the major and minor ABI version numbers of the library
you linked against by calling the functions C<ev_version_major> and
C<ev_version_minor>. If you want, you can compare against the global
symbols C<EV_VERSION_MAJOR> and C<EV_VERSION_MINOR>, which specify the
version of the library your program was compiled against.
+These version numbers refer to the ABI version of the library, not the
+release version.
+
Usually, it's a good idea to terminate if the major versions mismatch,
-as this indicates an incompatible change. Minor versions are usually
+as this indicates an incompatible change. Minor versions are usually
compatible to older versions, so a larger minor version alone is usually
not a problem.
=item C<EVBACKEND_EPOLL> (value 4, Linux)
For few fds, this backend is a bit little slower than poll and select,
-but it scales phenomenally better. While poll and select usually scale like
-O(total_fds) where n is the total number of fds (or the highest fd), epoll scales
-either O(1) or O(active_fds).
-
-While stopping and starting an I/O watcher in the same iteration will
-result in some caching, there is still a syscall per such incident
+but it scales phenomenally better. While poll and select usually scale
+like O(total_fds) where n is the total number of fds (or the highest fd),
+epoll scales either O(1) or O(active_fds). The epoll design has a number
+of shortcomings, such as silently dropping events in some hard-to-detect
+cases and rewuiring a syscall per fd change, no fork support and bad
+support for dup:
+
+While stopping, setting and starting an I/O watcher in the same iteration
+will result in some caching, there is still a syscall per such incident
(because the fd could point to a different file description now), so its
-best to avoid that. Also, dup()ed file descriptors might not work very
-well if you register events for both fds.
+best to avoid that. Also, C<dup ()>'ed file descriptors might not work
+very well if you register events for both fds.
Please note that epoll sometimes generates spurious notifications, so you
need to use non-blocking I/O or other means to avoid blocking when no data
=item C<EVBACKEND_KQUEUE> (value 8, most BSD clones)
Kqueue deserves special mention, as at the time of this writing, it
-was broken on all BSDs except NetBSD (usually it doesn't work with
-anything but sockets and pipes, except on Darwin, where of course its
-completely useless). For this reason its not being "autodetected"
+was broken on I<all> BSDs (usually it doesn't work with anything but
+sockets and pipes, except on Darwin, where of course it's completely
+useless. On NetBSD, it seems to work for all the FD types I tested, so it
+is used by default there). For this reason it's not being "autodetected"
unless you explicitly specify it explicitly in the flags (i.e. using
-C<EVBACKEND_KQUEUE>).
+C<EVBACKEND_KQUEUE>) or libev was compiled on a known-to-be-good (-enough)
+system like NetBSD.
It scales in the same way as the epoll backend, but the interface to the
-kernel is more efficient (which says nothing about its actual speed, of
-course). While starting and stopping an I/O watcher does not cause an
-extra syscall as with epoll, it still adds up to four event changes per
-incident, so its best to avoid that.
+kernel is more efficient (which says nothing about its actual speed,
+of course). While stopping, setting and starting an I/O watcher does
+never cause an extra syscall as with epoll, it still adds up to two event
+changes per incident, support for C<fork ()> is very bad and it drops fds
+silently in similarly hard-to-detetc cases.
=item C<EVBACKEND_DEVPOLL> (value 16, Solaris 8)
=item C<EVBACKEND_PORT> (value 32, Solaris 10)
-This uses the Solaris 10 port mechanism. As with everything on Solaris,
+This uses the Solaris 10 event port mechanism. As with everything on Solaris,
it's really slow, but it still scales very well (O(active_fds)).
-Please note that solaris ports can result in a lot of spurious
+Please note that solaris event ports can deliver a lot of spurious
notifications, so you need to use non-blocking I/O or other means to avoid
blocking when no data (or space) is available.
sense, so e.g. C<ev_is_active> might still return true. It is your
responsibility to either stop all watchers cleanly yoursef I<before>
calling this function, or cope with the fact afterwards (which is usually
-the easiest thing, youc na just ignore the watchers and/or C<free ()> them
+the easiest thing, you can just ignore the watchers and/or C<free ()> them
for example).
+Note that certain global state, such as signal state, will not be freed by
+this function, and related watchers (such as signal and child watchers)
+would need to be stopped manually.
+
+In general it is not advisable to call this function except in the
+rare occasion where you really need to free e.g. the signal handling
+pipe fds. If you need dynamically allocated loops it is better to use
+C<ev_loop_new> and C<ev_loop_destroy>).
+
=item ev_loop_destroy (loop)
Like C<ev_default_destroy>, but destroys an event loop created by an
received events and started processing them. This timestamp does not
change as long as callbacks are being processed, and this is also the base
time used for relative timers. You can treat it as the timestamp of the
-event occuring (or more correctly, libev finding out about it).
+event occurring (or more correctly, libev finding out about it).
=item ev_loop (loop, int flags)
Here are the gory details of what C<ev_loop> does:
+ - Before the first iteration, call any pending watchers.
* If there are no active watchers (reference count is zero), return.
- - Queue prepare watchers and then call all outstanding watchers.
+ - Queue all prepare watchers and then call all outstanding watchers.
- If we have been forked, recreate the kernel state.
- Update the kernel state with all outstanding changes.
- Update the "event loop time".
such as poll (fortunately in our Xlib example, Xlib already does this on
its own, so its quite safe to use).
+=head3 The special problem of disappearing file descriptors
+
+Some backends (e.g. kqueue, epoll) need to be told about closing a file
+descriptor (either by calling C<close> explicitly or by any other means,
+such as C<dup>). The reason is that you register interest in some file
+descriptor, but when it goes away, the operating system will silently drop
+this interest. If another file descriptor with the same number then is
+registered with libev, there is no efficient way to see that this is, in
+fact, a different file descriptor.
+
+To avoid having to explicitly tell libev about such cases, libev follows
+the following policy: Each time C<ev_io_set> is being called, libev
+will assume that this is potentially a new file descriptor, otherwise
+it is assumed that the file descriptor stays the same. That means that
+you I<have> to call C<ev_io_set> (or C<ev_io_init>) when you change the
+descriptor even if the file descriptor number itself did not change.
+
+This is how one would do it normally anyway, the important point is that
+the libev application should not optimise around libev but should leave
+optimisations to libev.
+
+=head3 The special problem of dup'ed file descriptors
+
+Some backends (e.g. epoll), cannot register events for file descriptors,
+but only events for the underlying file descriptions. That menas when you
+have C<dup ()>'ed file descriptors and register events for them, only one
+file descriptor might actually receive events.
+
+There is no workaorund possible except not registering events
+for potentially C<dup ()>'ed file descriptors or to resort to
+C<EVBACKEND_SELECT> or C<EVBACKEND_POLL>.
+
+=head3 The special problem of fork
+
+Some backends (epoll, kqueue) do not support C<fork ()> at all or exhibit
+useless behaviour. Libev fully supports fork, but needs to be told about
+it in the child.
+
+To support fork in your programs, you either have to call
+C<ev_default_fork ()> or C<ev_loop_fork ()> after a fork in the child,
+enable C<EVFLAG_FORKCHECK>, or resort to C<EVBACKEND_SELECT> or
+C<EVBACKEND_POLL>.
+
+
+=head3 Watcher-Specific Functions
+
=over 4
=item ev_io_init (ev_io *, callback, int fd, int events)
but if multiple timers become ready during the same loop iteration then
order of execution is undefined.
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_timer_init (ev_timer *, callback, ev_tstamp after, ev_tstamp repeat)
periodic watcher to trigger in 10 seconds (by specifiying e.g. C<ev_now ()
+ 10.>) and then reset your system clock to the last year, then it will
take a year to trigger the event (unlike an C<ev_timer>, which would trigger
-roughly 10 seconds later and of course not if you reset your system time
-again).
+roughly 10 seconds later).
They can also be used to implement vastly more complex timers, such as
-triggering an event on eahc midnight, local time.
+triggering an event on each midnight, local time or other, complicated,
+rules.
As with timers, the callback is guarenteed to be invoked only when the
time (C<at>) has been passed, but if multiple periodic timers become ready
during the same loop iteration then order of execution is undefined.
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_periodic_init (ev_periodic *, callback, ev_tstamp at, ev_tstamp interval, reschedule_cb)
=over 4
-=item * absolute timer (interval = reschedule_cb = 0)
+=item * absolute timer (at = time, interval = reschedule_cb = 0)
In this configuration the watcher triggers an event at the wallclock time
C<at> and doesn't repeat. It will not adjust when a time jump occurs,
that is, if it is to be run at January 1st 2011 then it will run when the
system time reaches or surpasses this time.
-=item * non-repeating interval timer (interval > 0, reschedule_cb = 0)
+=item * non-repeating interval timer (at = offset, interval > 0, reschedule_cb = 0)
In this mode the watcher will always be scheduled to time out at the next
-C<at + N * interval> time (for some integer N) and then repeat, regardless
-of any time jumps.
+C<at + N * interval> time (for some integer N, which can also be negative)
+and then repeat, regardless of any time jumps.
This can be used to create timers that do not drift with respect to system
time:
C<ev_periodic> will try to run the callback in this mode at the next possible
time where C<time = at (mod interval)>, regardless of any time jumps.
-=item * manual reschedule mode (reschedule_cb = callback)
+For numerical stability it is preferable that the C<at> value is near
+C<ev_now ()> (the current time), but there is no range requirement for
+this value.
+
+=item * manual reschedule mode (at and interval ignored, reschedule_cb = callback)
In this mode the values for C<interval> and C<at> are both being
ignored. Instead, each time the periodic watcher gets scheduled, the
NOTE: I<This callback MUST NOT stop or destroy any periodic watcher,
ever, or make any event loop modifications>. If you need to stop it,
return C<now + 1e30> (or so, fudge fudge) and stop it afterwards (e.g. by
-starting a prepare watcher).
+starting an C<ev_prepare> watcher, which is legal).
Its prototype is C<ev_tstamp (*reschedule_cb)(struct ev_periodic *w,
ev_tstamp now)>, e.g.:
a different time than the last time it was called (e.g. in a crond like
program when the crontabs have changed).
+=item ev_tstamp offset [read-write]
+
+When repeating, this contains the offset value, otherwise this is the
+absolute point in time (the C<at> value passed to C<ev_periodic_set>).
+
+Can be modified any time, but changes only take effect when the periodic
+timer fires or C<ev_periodic_again> is being called.
+
=item ev_tstamp interval [read-write]
The current interval value. Can be modified any time, but changes only
switched off. Can be changed any time, but changes only take effect when
the periodic timer fires or C<ev_periodic_again> is being called.
+=item ev_tstamp at [read-only]
+
+When active, contains the absolute time that the watcher is supposed to
+trigger next.
+
=back
Example: Call a callback every hour, or, more precisely, whenever the
watcher for a signal is stopped libev will reset the signal handler to
SIG_DFL (regardless of what it was set to before).
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_signal_init (ev_signal *, callback, int signum)
Child watchers trigger when your process receives a SIGCHLD in response to
some child status changes (most typically when a child of yours dies).
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_child_init (ev_child *, callback, int pid)
usually detected immediately, and if the file exists there will be no
polling.
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_stat_init (ev_stat *, callback, const char *path, ev_tstamp interval)
"pseudo-background processing", or delay processing stuff to after the
event loop has handled all outstanding events.
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_idle_init (ev_signal *, callback)
loop from blocking if lower-priority coroutines are active, thus mapping
low-priority coroutines to idle/background tasks).
+It is recommended to give C<ev_check> watchers highest (C<EV_MAXPRI>)
+priority, to ensure that they are being run before any other watchers
+after the poll. Also, C<ev_check> watchers (and C<ev_prepare> watchers,
+too) should not activate ("feed") events into libev. While libev fully
+supports this, they will be called before other C<ev_check> watchers did
+their job. As C<ev_check> watchers are often used to embed other event
+loops those other event loops might be in an unusable state until their
+C<ev_check> watcher ran (always remind yourself to coexist peacefully with
+others).
+
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_prepare_init (ev_prepare *, callback)
=back
-Example: To include a library such as adns, you would add IO watchers
-and a timeout watcher in a prepare handler, as required by libadns, and
-in a check watcher, destroy them and call into libadns. What follows is
-pseudo-code only of course:
+There are a number of principal ways to embed other event loops or modules
+into libev. Here are some ideas on how to include libadns into libev
+(there is a Perl module named C<EV::ADNS> that does this, which you could
+use for an actually working example. Another Perl module named C<EV::Glib>
+embeds a Glib main context into libev, and finally, C<Glib::EV> embeds EV
+into the Glib event loop).
+
+Method 1: Add IO watchers and a timeout watcher in a prepare handler,
+and in a check watcher, destroy them and call into libadns. What follows
+is pseudo-code only of course. This requires you to either use a low
+priority for the check watcher or use C<ev_clear_pending> explicitly, as
+the callbacks for the IO/timeout watchers might not have been called yet.
static ev_io iow [nfd];
static ev_timer tw;
static void
io_cb (ev_loop *loop, ev_io *w, int revents)
{
- // set the relevant poll flags
- // could also call adns_processreadable etc. here
- struct pollfd *fd = (struct pollfd *)w->data;
- if (revents & EV_READ ) fd->revents |= fd->events & POLLIN;
- if (revents & EV_WRITE) fd->revents |= fd->events & POLLOUT;
}
// create io watchers for each fd and a timer before blocking
ev_timer_init (&tw, 0, timeout * 1e-3);
ev_timer_start (loop, &tw);
- // create on ev_io per pollfd
+ // create one ev_io per pollfd
for (int i = 0; i < nfd; ++i)
{
ev_io_init (iow + i, io_cb, fds [i].fd,
| (fds [i].events & POLLOUT ? EV_WRITE : 0)));
fds [i].revents = 0;
- iow [i].data = fds + i;
ev_io_start (loop, iow + i);
}
}
ev_timer_stop (loop, &tw);
for (int i = 0; i < nfd; ++i)
- ev_io_stop (loop, iow + i);
+ {
+ // set the relevant poll flags
+ // could also call adns_processreadable etc. here
+ struct pollfd *fd = fds + i;
+ int revents = ev_clear_pending (iow + i);
+ if (revents & EV_READ ) fd->revents |= fd->events & POLLIN;
+ if (revents & EV_WRITE) fd->revents |= fd->events & POLLOUT;
+
+ // now stop the watcher
+ ev_io_stop (loop, iow + i);
+ }
adns_afterpoll (adns, fds, nfd, timeval_from (ev_now (loop));
}
+Method 2: This would be just like method 1, but you run C<adns_afterpoll>
+in the prepare watcher and would dispose of the check watcher.
+
+Method 3: If the module to be embedded supports explicit event
+notification (adns does), you can also make use of the actual watcher
+callbacks, and only destroy/create the watchers in the prepare watcher.
+
+ static void
+ timer_cb (EV_P_ ev_timer *w, int revents)
+ {
+ adns_state ads = (adns_state)w->data;
+ update_now (EV_A);
+
+ adns_processtimeouts (ads, &tv_now);
+ }
+
+ static void
+ io_cb (EV_P_ ev_io *w, int revents)
+ {
+ adns_state ads = (adns_state)w->data;
+ update_now (EV_A);
+
+ if (revents & EV_READ ) adns_processreadable (ads, w->fd, &tv_now);
+ if (revents & EV_WRITE) adns_processwriteable (ads, w->fd, &tv_now);
+ }
+
+ // do not ever call adns_afterpoll
+
+Method 4: Do not use a prepare or check watcher because the module you
+want to embed is too inflexible to support it. Instead, youc na override
+their poll function. The drawback with this solution is that the main
+loop is now no longer controllable by EV. The C<Glib::EV> module does
+this.
+
+ static gint
+ event_poll_func (GPollFD *fds, guint nfds, gint timeout)
+ {
+ int got_events = 0;
+
+ for (n = 0; n < nfds; ++n)
+ // create/start io watcher that sets the relevant bits in fds[n] and increment got_events
+
+ if (timeout >= 0)
+ // create/start timer
+
+ // poll
+ ev_loop (EV_A_ 0);
+
+ // stop timer again
+ if (timeout >= 0)
+ ev_timer_stop (EV_A_ &to);
+
+ // stop io watchers again - their callbacks should have set
+ for (n = 0; n < nfds; ++n)
+ ev_io_stop (EV_A_ iow [n]);
+
+ return got_events;
+ }
+
=head2 C<ev_embed> - when one backend isn't enough...
This is a rather advanced watcher type that lets you embed one event loop
into another (currently only C<ev_io> events are supported in the embedded
loop, other types of watchers might be handled in a delayed or incorrect
-fashion and must not be used).
+fashion and must not be used). (See portability notes, below).
There are primarily two reasons you would want that: work around bugs and
prioritise I/O.
else
loop_lo = loop_hi;
+=head2 Portability notes
+
+Kqueue is nominally embeddable, but this is broken on all BSDs that I
+tried, in various ways. Usually the embedded event loop will simply never
+receive events, sometimes it will only trigger a few times, sometimes in a
+loop. Epoll is also nominally embeddable, but many Linux kernel versions
+will always eport the epoll fd as ready, even when no events are pending.
+
+While libev allows embedding these backends (they are contained in
+C<ev_embeddable_backends ()>), take extreme care that it will actually
+work.
+
+When in doubt, create a dynamic event loop forced to use sockets (this
+usually works) and possibly another thread and a pipe or so to report to
+your main event loop.
+
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_embed_init (ev_embed *, callback, struct ev_loop *embedded_loop)
similarly to C<ev_loop (embedded_loop, EVLOOP_NONBLOCK)>, but in the most
apropriate way for embedded loops.
-=item struct ev_loop *loop [read-only]
+=item struct ev_loop *other [read-only]
The embedded event loop.
C<ev_default_fork> cheats and calls it in the wrong process, the fork
handlers will be invoked, too, of course.
+=head3 Watcher-Specific Functions and Data Members
+
=over 4
=item ev_fork_init (ev_signal *, callback)
Stops the watcher if it is active. Again, no C<loop> argument.
-=item w->again () C<ev::timer>, C<ev::periodic> only
+=item w->again () (C<ev::timer>, C<ev::periodic> only)
For C<ev::timer> and C<ev::periodic>, this invokes the corresponding
C<ev_TYPE_again> function.
-=item w->sweep () C<ev::embed> only
+=item w->sweep () (C<ev::embed> only)
Invokes C<ev_embed_sweep>.
-=item w->update () C<ev::stat> only
+=item w->update () (C<ev::stat> only)
Invokes C<ev_stat_stat>.
=head1 MACRO MAGIC
-Libev can be compiled with a variety of options, the most fundemantal is
-C<EV_MULTIPLICITY>. This option determines whether (most) functions and
-callbacks have an initial C<struct ev_loop *> argument.
+Libev can be compiled with a variety of options, the most fundamantal
+of which is C<EV_MULTIPLICITY>. This option determines whether (most)
+functions and callbacks have an initial C<struct ev_loop *> argument.
To make it easier to write programs that cope with either variant, the
following macros are defined:
Game Server, the EV perl module, the GNU Virtual Private Ethernet (gvpe)
and rxvt-unicode.
-The goal is to enable you to just copy the neecssary files into your
+The goal is to enable you to just copy the necessary files into your
source directory without having to change even a single line in them, so
you can easily upgrade by simply copying (or having a checked-out copy of
libev somewhere in your source tree).
monotonic clock option at both compiletime and runtime. Otherwise no use
of the monotonic clock option will be attempted. If you enable this, you
usually have to link against librt or something similar. Enabling it when
-the functionality isn't available is safe, though, althoguh you have
+the functionality isn't available is safe, though, although you have
to make sure you link against any libraries where the C<clock_gettime>
function is hiding in (often F<-lrt>).
realtime clock option at compiletime (and assume its availability at
runtime if successful). Otherwise no use of the realtime clock option will
be attempted. This effectively replaces C<gettimeofday> by C<clock_get
-(CLOCK_REALTIME, ...)> and will not normally affect correctness. See tzhe note about libraries
-in the description of C<EV_USE_MONOTONIC>, though.
+(CLOCK_REALTIME, ...)> and will not normally affect correctness. See the
+note about libraries in the description of C<EV_USE_MONOTONIC>, though.
=item EV_USE_SELECT
Can be used to change the callback member declaration in each watcher,
and the way callbacks are invoked and set. Must expand to a struct member
-definition and a statement, respectively. See the F<ev.v> header file for
+definition and a statement, respectively. See the F<ev.h> header file for
their default definitions. One possible use for overriding these is to
avoid the C<struct ev_loop *> as first argument in all cases, or to use
method calls instead of plain function calls in C++.
+=head2 EXPORTED API SYMBOLS
+
+If you need to re-export the API (e.g. via a dll) and you need a list of
+exported symbols, you can use the provided F<Symbol.*> files which list
+all public symbols, one per line:
+
+ Symbols.ev for libev proper
+ Symbols.event for the libevent emulation
+
+This can also be used to rename all public symbols to avoid clashes with
+multiple versions of libev linked together (which is obviously bad in
+itself, but sometimes it is inconvinient to avoid this).
+
+A sed command like this will create wrapper C<#define>'s that you need to
+include before including F<ev.h>:
+
+ <Symbols.ev sed -e "s/.*/#define & myprefix_&/" >wrap.h
+
+This would create a file F<wrap.h> which essentially looks like this:
+
+ #define ev_backend myprefix_ev_backend
+ #define ev_check_start myprefix_ev_check_start
+ #define ev_check_stop myprefix_ev_check_stop
+ ...
+
=head2 EXAMPLES
For a real-world example of a program the includes libev
projects / software / libev.git / blobdiff