*** empty log message ***

[software/libev.git] / ev.pod

diff --git a/ev.pod b/ev.pod
index 063c01dbdeb76dc4c75fe96705aad8e2e79db12c..905e935ccbbb3af9e2027e1fd0a04222c14b8931 100644 (file)
--- a/ev.pod
+++ b/ev.pod
@@ -913,6 +913,30 @@ whether a file descriptor is really ready with a known-to-be good interface
 such as poll (fortunately in our Xlib example, Xlib already does this on
 its own, so its quite safe to use).
 
+=head3 The special problem of disappearing file descriptors
+
+Some backends (e.g kqueue, epoll) need to be told about closing a file
+descriptor (either by calling C<close> explicitly or by any other means,
+such as C<dup>). The reason is that you register interest in some file
+descriptor, but when it goes away, the operating system will silently drop
+this interest. If another file descriptor with the same number then is
+registered with libev, there is no efficient way to see that this is, in
+fact, a different file descriptor.
+
+To avoid having to explicitly tell libev about such cases, libev follows
+the following policy:  Each time C<ev_io_set> is being called, libev
+will assume that this is potentially a new file descriptor, otherwise
+it is assumed that the file descriptor stays the same. That means that
+you I<have> to call C<ev_io_set> (or C<ev_io_init>) when you change the
+descriptor even if the file descriptor number itself did not change.
+
+This is how one would do it normally anyway, the important point is that
+the libev application should not optimise around libev but should leave
+optimisations to libev.
+
+
+=head3 Watcher-Specific Functions
+
 =over 4
 
 =item ev_io_init (ev_io *, callback, int fd, int events)
@@ -975,6 +999,8 @@ The callback is guarenteed to be invoked only when its timeout has passed,
 but if multiple timers become ready during the same loop iteration then
 order of execution is undefined.
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_timer_init (ev_timer *, callback, ev_tstamp after, ev_tstamp repeat)
@@ -1089,6 +1115,8 @@ As with timers, the callback is guarenteed to be invoked only when the
 time (C<at>) has been passed, but if multiple periodic timers become ready
 during the same loop iteration then order of execution is undefined.
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_periodic_init (ev_periodic *, callback, ev_tstamp at, ev_tstamp interval, reschedule_cb)
@@ -1244,6 +1272,8 @@ as you don't register any with libev). Similarly, when the last signal
 watcher for a signal is stopped libev will reset the signal handler to
 SIG_DFL (regardless of what it was set to before).
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_signal_init (ev_signal *, callback, int signum)
@@ -1265,6 +1295,8 @@ The signal the watcher watches out for.
 Child watchers trigger when your process receives a SIGCHLD in response to
 some child status changes (most typically when a child of yours dies).
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_child_init (ev_child *, callback, int pid)
@@ -1342,6 +1374,8 @@ to fall back to regular polling again even with inotify, but changes are
 usually detected immediately, and if the file exists there will be no
 polling.
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_stat_init (ev_stat *, callback, const char *path, ev_tstamp interval)
@@ -1433,6 +1467,8 @@ effect on its own sometimes), idle watchers are a good place to do
 "pseudo-background processing", or delay processing stuff to after the
 event loop has handled all outstanding events.
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_idle_init (ev_signal *, callback)
@@ -1509,6 +1545,8 @@ loops those other event loops might be in an unusable state until their
 C<ev_check> watcher ran (always remind yourself to coexist peacefully with
 others).
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_prepare_init (ev_prepare *, callback)
@@ -1719,6 +1757,8 @@ create it, and if that fails, use the normal loop for everything:
   else
     loop_lo = loop_hi;
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_embed_init (ev_embed *, callback, struct ev_loop *embedded_loop)
@@ -1754,6 +1794,8 @@ and only in the child after the fork. If whoever good citizen calling
 C<ev_default_fork> cheats and calls it in the wrong process, the fork
 handlers will be invoked, too, of course.
 
+=head3 Watcher-Specific Functions and Data Members
+
 =over 4
 
 =item ev_fork_init (ev_signal *, callback)
@@ -1979,16 +2021,16 @@ constructor already stores the event loop.
 
 Stops the watcher if it is active. Again, no C<loop> argument.
 
-=item w->again ()       C<ev::timer>, C<ev::periodic> only
+=item w->again () (C<ev::timer>, C<ev::periodic> only)
 
 For C<ev::timer> and C<ev::periodic>, this invokes the corresponding
 C<ev_TYPE_again> function.
 
-=item w->sweep ()       C<ev::embed> only
+=item w->sweep () (C<ev::embed> only)
 
 Invokes C<ev_embed_sweep>.
 
-=item w->update ()      C<ev::stat> only
+=item w->update () (C<ev::stat> only)
 
 Invokes C<ev_stat_stat>.
 
@@ -2018,9 +2060,9 @@ the constructor.
 
 =head1 MACRO MAGIC
 
-Libev can be compiled with a variety of options, the most fundemantal is
-C<EV_MULTIPLICITY>. This option determines whether (most) functions and
-callbacks have an initial C<struct ev_loop *> argument.
+Libev can be compiled with a variety of options, the most fundamantal
+of which is C<EV_MULTIPLICITY>. This option determines whether (most)
+functions and callbacks have an initial C<struct ev_loop *> argument.
 
 To make it easier to write programs that cope with either variant, the
 following macros are defined: