<meta name="description" content="Pod documentation for libev" />
<meta name="inputfile" content="<standard input>" />
<meta name="outputfile" content="<standard output>" />
- <meta name="created" content="Wed Nov 28 19:29:25 2007" />
+ <meta name="created" content="Thu Nov 29 21:05:58 2007" />
<meta name="generator" content="Pod::Xhtml 1.57" />
<link rel="stylesheet" href="http://res.tst.eu/pod.css"/></head>
<body>
override the flags completely if it is found in the environment. This is
useful to try out specific backends to test their performance, or to work
around bugs.</p>
+ </dd>
+ <dt><code>EVFLAG_FORKCHECK</code></dt>
+ <dd>
+ <p>Instead of calling <code>ev_default_fork</code> or <code>ev_loop_fork</code> manually after
+a fork, you can also make libev check for a fork in each iteration by
+enabling this flag.</p>
+ <p>This works by calling <code>getpid ()</code> on every iteration of the loop,
+and thus this might slow down your event loop if you do a lot of loop
+iterations and little real work, but is usually not noticable (on my
+Linux system for example, <code>getpid</code> is actually a simple 5-insn sequence
+without a syscall and thus <i>very</i> fast, but my Linux system also has
+<code>pthread_atfork</code> which is even faster).</p>
+ <p>The big advantage of this flag is that you can forget about fork (and
+forget about forgetting to tell libev about forking) when you use this
+flag.</p>
+ <p>This flag setting cannot be overriden or specified in the <code>LIBEV_FLAGS</code>
+environment variable.</p>
</dd>
<dt><code>EVBACKEND_SELECT</code> (value 1, portable select backend)</dt>
<dd>
<dd>
<p>This will act as if the timer timed out and restart it again if it is
repeating. The exact semantics are:</p>
- <p>If the timer is started but nonrepeating, stop it.</p>
- <p>If the timer is repeating, either start it if necessary (with the repeat
-value), or reset the running timer to the repeat value.</p>
+ <p>If the timer is pending, its pending status is cleared.</p>
+ <p>If the timer is started but nonrepeating, stop it (as if it timed out).</p>
+ <p>If the timer is repeating, either start it if necessary (with the
+<code>repeat</code> value), or reset the running timer to the <code>repeat</code> value.</p>
<p>This sounds a bit complicated, but here is a useful and typical
-example: Imagine you have a tcp connection and you want a so-called
-idle timeout, that is, you want to be called when there have been,
-say, 60 seconds of inactivity on the socket. The easiest way to do
-this is to configure an <code>ev_timer</code> with <code>after</code>=<code>repeat</code>=<code>60</code> and calling
+example: Imagine you have a tcp connection and you want a so-called idle
+timeout, that is, you want to be called when there have been, say, 60
+seconds of inactivity on the socket. The easiest way to do this is to
+configure an <code>ev_timer</code> with a <code>repeat</code> value of <code>60</code> and then call
<code>ev_timer_again</code> each time you successfully read or write some data. If
you go into an idle state where you do not expect data to travel on the
-socket, you can stop the timer, and again will automatically restart it if
-need be.</p>
- <p>You can also ignore the <code>after</code> value and <code>ev_timer_start</code> altogether
-and only ever use the <code>repeat</code> value:</p>
+socket, you can <code>ev_timer_stop</code> the timer, and <code>ev_timer_again</code> will
+automatically restart it if need be.</p>
+ <p>That means you can ignore the <code>after</code> value and <code>ev_timer_start</code>
+altogether and only ever use the <code>repeat</code> value and <code>ev_timer_again</code>:</p>
<pre> ev_timer_init (timer, callback, 0., 5.);
ev_timer_again (loop, timer);
...
ev_timer_again (loop, timer);
</pre>
- <p>This is more efficient then stopping/starting the timer eahc time you want
-to modify its timeout value.</p>
+ <p>This is more slightly efficient then stopping/starting the timer each time
+you want to modify its timeout value.</p>
</dd>
<dt>ev_tstamp repeat [read-write]</dt>
<dd>
loop, if multiple loops are supported ("ev loop default").</p>
</dd>
</dl>
-<p>Example: Declare and initialise a check watcher, working regardless of
-wether multiple loops are supported or not.</p>
+<p>Example: Declare and initialise a check watcher, utilising the above
+macros so it will work regardless of wether multiple loops are supported
+or not.</p>
<pre> static void
check_cb (EV_P_ ev_timer *w, int revents)
{
ev_check_start (EV_DEFAULT_ &check);
ev_loop (EV_DEFAULT_ 0);
-
-
-
</pre>
</div>
ev_win32.c required on win32 platforms only
- ev_select.c only when select backend is enabled (which is by default)
+ ev_select.c only when select backend is enabled (which is enabled by default)
ev_poll.c only when poll backend is enabled (disabled by default)
ev_epoll.c only when the epoll backend is enabled (disabled by default)
ev_kqueue.c only when the kqueue backend is enabled (disabled by default)
will be compiled. It is pretty complex because it provides its own header
file.</p>
<p>The usage in rxvt-unicode is simpler. It has a <cite>ev_cpp.h</cite> header file
-that everybody includes and which overrides some autoconf choices:</p>
-<pre> #define EV_USE_POLL 0
+that everybody includes and which overrides some configure choices:</p>
+<pre> #define EV_MINIMAL 1
+ #define EV_USE_POLL 0
#define EV_MULTIPLICITY 0
- #define EV_PERIODICS 0
+ #define EV_PERIODIC_ENABLE 0
+ #define EV_STAT_ENABLE 0
+ #define EV_FORK_ENABLE 0
#define EV_CONFIG_H <config.h>
+ #define EV_MINPRI 0
+ #define EV_MAXPRI 0
#include "ev++.h"
projects / software / libev.git / blobdiff